Skip to content

How To Replace A Ceramic Disc Cartridge

If you are experiencing low water pressure, leaking taps, or no water coming out of your taps at all, it is likely that you need to replace your ceramic disc cartridge. This guide will show you how to do just that.

How To Replace A Ceramic Disc Cartridge

Replacing a ceramic disc cartridge is a fairly simple process that can be done in a few minutes. The most important thing to remember is to turn off the water supply before beginning the replacement process. The first step is to remove the handle from the faucet. This can be done by unscrewing the cap on the handle and pulling it straight off. Once the handle is removed, the retaining clip should be visible. The clip can be released by pressing down on

-Replacement ceramic cartridge -Pipe wrench -Channel locks -Teflon tape -New washer -Screwdriver

  • Turn off the water supply to the faucet by turning the valve handle in a clockwise direction
  • Open the faucet to release any pressure that may be built up in the lines
  • Remove the decorative cap

-Check the water supply valves to make sure they are open -Turn off the water supply to the faucet -Remove the handle by unscrewing it from the valve body -Unscrew the cartridge by turning it counterclockwise. If it is tight, you can use a cartridge wrench or pliers -Insert the new cartridge and turn it clockwise until it is tight -Reattach the handle and turn on the water supply


Frequently Asked Questions

How Do You Remove A Cartridge From A Mixer?

To remove a cartridge from a mixer, one needs to locate the release button on the mixer and release the cartridge. The cartridge can then be pulled out of the mixer.

How Do You Remove The Cartridge From A Tap Removal Tool?

To remove the cartridge from a tap removal tool, hold the tap removal tool with one hand and use the other hand to twist the cartridge counter-clockwise.

How Do You Change A Shower Mixer Tap Cartridge?

The process of changing a shower mixer tap cartridge is not difficult, but it can be a little messy. The first step is to shut off the water supply to the faucet. Next, remove the handle by unscrewing it counterclockwise. Once the handle is off, the cartridge can be accessed and removed by unscrewing it counterclockwise. Be sure to dispose of the old cartridge properly and install the new one in reverse order.

How Do You Remove A Mixer Tap Head?

There are a few ways to remove a mixer tap head. The easiest is to use a wrench or pliers to turn the tap head counterclockwise. If the tap is stuck, you can try to loosen it by soaking it in hot water for a few minutes first. Another option is to use a hacksaw to cut off the tap head, but this can be difficult and dangerous if you’re not careful.

How Do You Remove A Kitchen Faucet Cartridge?

Removing a kitchen faucet cartridge usually involves using a wrench to unscrew the cartridge from the faucet. Some cartridges may be held in place with a clip, which can be released by pressing down on it while pulling the cartridge out.

How Do I Change The Cartridge In My Shower Mixer?

To change the cartridge in your shower mixer, you will need to shut off the water supply, unscrew the old cartridge, and screw in the new cartridge.

Can You Replace Shower Cartridge Without Turning Off Water?

Yes, it is possible to replace a shower cartridge without turning off the water, but it is not recommended. Shutting off the water allows for a more controlled and thorough replacement process.

How Do I Remove A Tap Cartridge?

First, turn off the water supply to the tap. Second, use an adjustable wrench to loosen the large nut on the top of the cartridge. Third, twist and pull the cartridge out of the faucet. Finally, clean any debris or old sealant from the faucet and reattach the new cartridge.

How Do You Remove A Stubborn Faucet Cartridge?

There are a few ways to remove a stubborn faucet cartridge. One way is to use a cartridge puller. Another way is to try and pry the cartridge out using a screwdriver or other tool. If those methods don’t work, you can try heating up the cartridge with a hair dryer or heat gun to loosen the adhesive.

How Do You Change A Faucet Cartridge?

To change a faucet cartridge, you will need to remove the faucet handle, unscrew the cartridge and replace it with a new one. Be sure to follow the manufacturer’s instructions carefully.

How Do I Change A Tap Cartridge?

To change a tap cartridge, unscrew the old cartridge and screw in the new one.


To Summarize

Replacing a ceramic disc cartridge is a fairly simple process, although it can be a bit messy. First, shut off the water supply to the faucet and disconnect the water hoses. Next, remove the handle by unscrewing the retaining screw at the top of the faucet. Now you can remove the cartridge by unscrewing it from the valve assembly. Make sure to clean any old sealant or mineral deposits from the valve assembly before reassembling the faucet. Finally, reconnect the water hoses and turn on the water supply.

Leave a Reply

Your email address will not be published.